32-G, Jalan Puteri 5/16,
Bandar Puteri Puchong,
47100 Puchong,
Selangor, Malaysia.
+6011-1626 9527
Davor Sdn Bhd
32-G, Jalan Puteri 5/16,
Bandar Puteri Puchong,
47100 Puchong,
Selangor, Malaysia.
32-G, Jalan Puteri 5/16,
Bandar Puteri Puchong,
47100 Puchong,
Selangor, Malaysia.
Dye Penetrant Spray - Spanjaard Malaysia
Spanjaard Flaw & Crack Detector System
Product Description
Consists of 3 products for the convenient non-destructive testing of cracks and other surface flaws in metal components. The system is a fast, economical and reliable method of visual detection of all surface defects on metal parts during manufacture and also on operational components in-situ. The three pack system meets DTD 929/MIL-I-25135E Group I and II.
Product Description
Consists of 3 products for the convenient non-destructive testing of cracks and other surface flaws in metal components. The system is a fast, economical and reliable method of visual detection of all surface defects on metal parts during manufacture and also on operational components in-situ. The three pack system meets DTD 929/MIL-I-25135E Group I and II.
Applications
Spanjaard Flaw & Crack Detector System is designed for use on all metals including Titanium, Nickel, Stainless Steel and Aluminium, which require product to be formulated with low halogen and sulphur content (meets NDT tests of Welding Institute).
These system is made up of:-
1. A solvent cleaner to remove surface contamination (Pack No. 1).
2. A red dye penetrant i.e. a dye solution in a low viscosity solvent mixture that will penetrate any crack or fault and will not dry too quickly (Pack No. 2).
3. A white developer, to coat the surface with a fine, absorbent white powder which will draw out any dye held in the cracks which are then revealed as coloured areas in a white background (Pack No. 3).
The Spanjaard Flaw & Crack Detector System will show up cracks as red lines and porous areas as red pin points on all types of metal. Typical fields of application include weld inspection, routine maintenance inspection, Inspection and checking of tools or incoming materials, etc.
The detector system can be used as applications below:
- When an undetected defect in raw material or finished component can become a dangerous fracture.
- Checking for potential fatigue cracks or flaws during maintenance where parts of vehicles, cranes and other equipment are subjected to heavy stress.
- Inspection of welded areas that must be free of flaws e.g. industrial heating equipment oil tanks fabricated from mild steel.
- Machined surfaces or parts of equipment used for pressing operations.
- Aluminium die-castings can be examined for minute flaws or cracks.
Application Instruction
The Spanjaard Flaw & Crack Detector System is available as a three pack aerosol. The Three Pack System should be used as follows:
1) Cleaner
Remove all surface contamination such as oil, grease and dust. Spray surface with cleaner (Pack 1) and clean thoroughly with absorbent cloth until no further contamination is evident on the cloth/tissue.
2) Penetrant
Parts must be at ambient temperature before spraying. Liberally spray the area with Penetrant (Pack 2) and allow 5 minutes contact time. Allow up to 20 minutes for very fine cracks.
3) Cleaner
Spray Cleaner (Pack 1) onto an absorbent lint-free cloth and wipe off excess from surface until no further Penetrant (Pack 2) is evident on the cloth. This step is vital to ensure cracks and flaws are detected.
4) Developer
Shake container before use. Spray on a thin, even film of Developer (Pack 3) and leave on for at least 10 minutes before inspecting for the fine flaws.
Typical Properties
| PACK 1 | PACK 2 | PACK 3 | |
| Colour | Colourles | Red | White |
| Odour | Ether-like | Distinct | Solvent |
| Density 25 Degree Celcius, g/ml | 0.79 | 0.79 | 0.85 |
| Flammability | Highly Flammable | Highly Flammable | Highly Flammable |
| pH | 7 | 7 | 7 |
Packaging
- Cleaner (Pack 1) 350ml Aerosol
- Penetrant (Pack 2) 300ml Aerosol
- Developer (Pack 3) 350ml Aerosol
Malaysia, Selangor (Klang, Puchong, Shah Alam, Subang), Kuala Lumpur (Sungai Buloh), Negeri Sembilan (Seremban), Melaka, Johor (Johor Bharu, Muar, Batu Pahat), Pahang (Temerloh, Kuantan), Kelantan (Kota Bahru), Terengganu (Kuala Terengganu), Perak (Ipoh), Kedah (Sungai Petani), Perlis, Penang (Bukit Mertajam, Butterworth, Seberang Prai), Sabah (Kota Kinabalu), Sarawak (Kuching), WP Putrajaya, WP Labuan, Indonesia, Singapore, Thailand, Philippines, Vietnam, Laos, Myanmar, Cambodia, Brunei