32-G, Jalan Puteri 5/16,
Bandar Puteri Puchong,
47100 Puchong,
Selangor, Malaysia.
+6011-1626 9527
Davor Sdn Bhd
32-G, Jalan Puteri 5/16,
Bandar Puteri Puchong,
47100 Puchong,
Selangor, Malaysia.
32-G, Jalan Puteri 5/16,
Bandar Puteri Puchong,
47100 Puchong,
Selangor, Malaysia.
Concrete Mould Oil - LUBTEX Lubricants Malaysia
- mould release oil
- timber release oil
- mould oil for formwork
- concrete mould oil supplier
- concrete mould oil malaysia
LUBTEX CONCRETE MOULD OIL
Product Description
DVOIL MOULD EX is a chemical release agent for both timber and steel formworks. It is blended with high efficient releasing properties agent to function as a bond breaker between formwork and fresh concrete.
Advantages
- Stain free on concrete.
- Provides protection to both timber and steel formworks as it acts as a rust inhibitor and water proofer.
- Ready to use and should not be diluted.
- Usable for all types of formworks.
Application Instuction
The surfaces to be coated with DVOIL MOULD EX must be clean and free from dirt, old concrete or greases.
Coverage
DVOIL MOULD EX should be applied at the following stated coverage rates to obtain a thin and even film over the entire surface of the formwork:
Typical Properties
Available Packing
200 liter drum
Contact our sales consultant in area:
Malaysia (Selangor(Klang, Shah Alam, Subang), Kuala Lumpur(Sungai Buloh), Sepang, Negeri Sembilan, Melaka, Johor(Johor Bharu,Muar,Batu Pahat), Pahang(Temerloh, Kuantan), Kelantan, Terengganu, Perak(Ipoh), Kedah, Perlis, Penang, Sabah, Sarawak), Indonesia, Singapore, Thailand, Philippines, Vietnam, Laos, Myanmar, Cambodia, Brunei.
Product Description
DVOIL MOULD EX is a chemical release agent for both timber and steel formworks. It is blended with high efficient releasing properties agent to function as a bond breaker between formwork and fresh concrete.
Advantages
- Provides protection to both timber and steel formworks as it acts as a rust inhibitor and water proofer.
- Ready to use and should not be diluted.
- Usable for all types of formworks.
Application
Use brush, sponge or spray equipment to apply on the formwork surface. Any excess liquid remaining on the surface after application should be mopped off. Allow 1-3 hours to dry before pouring concrete. lf the concrete pouring delayed more than 48 hours, the surface should be recoated.
Use brush, sponge or spray equipment to apply on the formwork surface. Any excess liquid remaining on the surface after application should be mopped off. Allow 1-3 hours to dry before pouring concrete. lf the concrete pouring delayed more than 48 hours, the surface should be recoated.
Application Instuction
The surfaces to be coated with DVOIL MOULD EX must be clean and free from dirt, old concrete or greases.
Coverage
DVOIL MOULD EX should be applied at the following stated coverage rates to obtain a thin and even film over the entire surface of the formwork:
- Timber formwork : 1 liter per 20m2
- Metal formwork : 1 liter per 31m2
Safety
Wear gloves and goggles during application. lf in contact with skin, wash thoroughly with soap and water. lf in contact with eyes or mucous membrane, flush immediately with plenty of water and seek medical attention without delay. Use with adequate ventilation.
Wear gloves and goggles during application. lf in contact with skin, wash thoroughly with soap and water. lf in contact with eyes or mucous membrane, flush immediately with plenty of water and seek medical attention without delay. Use with adequate ventilation.
Typical Properties
| Technical Data (Typical Value) | DAVOIL MOULD EX |
| Appearance, Visual | Brown Yellowish |
| Chemical Type | Oil Based |
| Density at 25 Degree Celcius | 0.9 |
Available Packing
200 liter drum
Contact our sales consultant in area:
Malaysia (Selangor(Klang, Shah Alam, Subang), Kuala Lumpur(Sungai Buloh), Sepang, Negeri Sembilan, Melaka, Johor(Johor Bharu,Muar,Batu Pahat), Pahang(Temerloh, Kuantan), Kelantan, Terengganu, Perak(Ipoh), Kedah, Perlis, Penang, Sabah, Sarawak), Indonesia, Singapore, Thailand, Philippines, Vietnam, Laos, Myanmar, Cambodia, Brunei.